- Latest available (Revised)
- Original (As adopted by EU)
Commission Regulation (EU) No 601/2012 of 21 June 2012 on the monitoring and reporting of greenhouse gas emissions pursuant to Directive 2003/87/EC of the European Parliament and of the Council (Text with EEA relevance) (repealed)
After exit day there will be three versions of this legislation to consult for different purposes. The legislation.gov.uk version is the version that applies in the UK. The EU Version currently on EUR-lex is the version that currently applies in the EU i.e you may need this if you operate a business in the EU.
The web archive version is the official version of this legislation item as it stood on exit day before being published to legislation.gov.uk and any subsequent UK changes and effects applied. The web archive also captured associated case law and other language formats from EUR-Lex.
This is the original version (as it was originally adopted).
PFC emissions shall be calculated from the emissions measurable in a duct or stack (‘point source emissions’) as well as fugitive emissions using the collection efficiency of the duct:
PFC emissions (total) = PFC emissions (duct)/collection efficiency
The collection efficiency shall be measured when the installation-specific emission factors are determined. For its determination the most recent version of the guidance mentioned under Tier 3 of section 4.4.2.4 of the 2006 IPCC Guidelines shall be used.
The operator shall calculate emissions of CF4 and C2F6 emitted through a duct or stack using one of the following methods:
Method A where the anode effect minutes per cell-day are recorded;
Method B where the anode effect overvoltage is recorded.
The operator shall use the following equations for determining PFC emissions:
CF4 emissions [t] = AEM × (SEFCF4/1 000) × PrAl
C2F6 emissions [t] = CF4 emissions * FC2F6
Where:
=
Anode effect minutes/cell-day;
=
Slope emission factor [(kg CF4/t Al produced)/(anode effect minutes/cell-day)]. Where different cell-types are used, different SEF may be applied as appropriate;
=
Annual production of primary Aluminium [t];
=
Weight fraction of C2F6 (t C2F6/t CF4).
The anode effect minutes per cell-day shall express the frequency of anode effects (number anode effects/cell-day) multiplied by the average duration of anode effects (anode effect minutes/occurrence):
AEM = frequency × average duration
:
The emission factor for CF4 (slope emission factor, SEFCF4) expresses the amount [kg] of CF4 emitted per tonne of aluminium produced per anode effect minute/cell-day. The emission factor (weight fraction FC2F6) of C2F6 expresses the amount [t] of C2F6 emitted proportionate to the amount [t] of CF4 emitted.
:
The operator shall use technology-specific emission factors from Table 1 of this section of Annex IV.
:
The operator shall use installation-specific emission factors for CF4 and C2F6 established through continuous or intermittent field measurements. For the determination of those emission factors the operator shall use the most recent version of the guidance mentioned under tier 3 of section 4.4.2.4 of the 2006 IPCC Guidelines(1). The operator shall determine each emission factor with a maximum uncertainty of ± 15 %.
The operator shall determine the emission factors at least every three years or earlier where necessary due to relevant changes at the installation. Relevant changes shall include a change in the distribution of anode effect duration, or a change in the control algorithm affecting the mix of the types of anode effects or the nature of the anode effect termination routine.
Technology | Emission factor for CF4 (SEFCF4)[(kg CF4/t Al)/(AE-Mins/cell-day)] | Emission factor for C2F6 (FC2F6)[t C2F6/t CF4] |
---|---|---|
Centre Worked Prebake (CWPB) | 0,143 | 0,121 |
Vertical Stud Søderberg (VSS) | 0,092 | 0,053 |
Where the anode effect overvoltage is measured, the operator shall use the following equations for the determination of PFC emissions:
CF4 emissions [t] = OVC × (AEO/CE) × PrAl × 0,001
C2F6 emissions [t] = CF4 emissions × FC2F6
Where:
=
Overvoltage coefficient (‘emission factor’) expressed as kg CF4 per tonne of aluminium produced per mV overvoltage;
=
Anode effect overvoltage per cell [mV] determined as the integral of (time × voltage above the target voltage) divided by the time (duration) of data collection;
=
Average current efficiency of aluminium production [%];
=
Annual production of primary Aluminium [t];
=
Weight fraction of C2F6 (t C2F6/t CF4);
The term AEO/CE (Anode effect overvoltage/current efficiency) expresses the time-integrated average anode effect overvoltage [mV overvoltage] per average current efficiency [%].
:
The emission factor for CF4 (‘overvoltage coefficient’ OVC) shall express the amount [kg] of CF4 emitted per tonne of aluminium produced per millivolt overvoltage [mV]. The emission factor of C2F6 (weight fraction FC2F6) shall express the amount [t] of C2F6 emitted proportionate to the amount [t] of CF4 emitted.
:
The operator shall apply technology-specific emission factors from Table 2 of this section of Annex IV.
:
The operator shall use installation-specific emission factors for CF4 [(kg CF4/t Al)/(mV)] and C2F6 [t C2F6/t CF4] established through continuous or intermittent field measurements. For the determination of those emission factors, the operator shall use the most recent version of the guidance mentioned under tier 3 of section 4.4.2.4 of the 2006 IPCC Guidelines. The operator shall determine the emission factors with a maximum uncertainty of ± 15 % each.
The operator shall determine the emission factors at least every three years or earlier where necessary due to relevant changes at the installation. Relevant changes shall include a change in the distribution of anode effect duration or a change in the control algorithm affecting the mix of the types of anode effects or the nature of the anode effect termination routine.
Technology | Emission factor for CF4[(kg CF4/t Al)/mV] | Emission factor for C2F6[t C2F6/t CF4] |
---|---|---|
Centre Worked Prebake (CWPB) | 1,16 | 0,121 |
Vertical Stud Søderberg (VSS) | N.A. | 0,053 |
International Aluminium Institute; The Aluminium Sector Greenhouse Gas Protocol; October 2006; US Environmental Protection Agency and International Aluminium Institute; Protocol for Measurement of Tetrafluoromethane (CF4) and Hexafluoroethane (C2F6) Emissions from Primary Aluminum Production; April 2008.
The Whole Regulation you have selected contains over 200 provisions and might take some time to download. You may also experience some issues with your browser, such as an alert box that a script is taking a long time to run.
Would you like to continue?
The Schedules you have selected contains over 200 provisions and might take some time to download. You may also experience some issues with your browser, such as an alert box that a script is taking a long time to run.
Would you like to continue?
Latest Available (revised):The latest available updated version of the legislation incorporating changes made by subsequent legislation and applied by our editorial team. Changes we have not yet applied to the text, can be found in the ‘Changes to Legislation’ area.
Original (As adopted by EU): The original version of the legislation as it stood when it was first adopted in the EU. No changes have been applied to the text.
Access essential accompanying documents and information for this legislation item from this tab. Dependent on the legislation item being viewed this may include:
Use this menu to access essential accompanying documents and information for this legislation item. Dependent on the legislation item being viewed this may include:
Click 'View More' or select 'More Resources' tab for additional information including: